Swirl generation is an important parameter inside the diesel engine cylinder as it achieves good mixing of air and fuel which has a great influence on the combustion efficiency, engine emissions, and soot formation. The generated swirl intensity by the inlet port and the inlet valve configuration is usually measured on a steady flow test rig using an impulse torque meter. In this paper, an experimental investigation using steady flow test rig was performed on an engine cylinder having a helical-spiral inlet port and shrouded inlet valve. Three valve shrouds were used, they are; 120o, 150o, and 180o. With each shroud, four orientation angles were used; they are 0o, 30o, 60o, and 90o. The experiments were performed under constant cylinder vacuum pressure of 350 mm H2O. The results showed that using shrouded inlet valve increases the swirl number at all valve shroud and orientation angles except for valve shroud angle of 180o and orientation angle of 90o. Also, using of shrouded inlet valve decreases the mass flow rate and the discharge coefficient at all valve shroud and orientation angles.

A numerical simulation of transport phenomena in the photo-electrochemical (PEC) reactor is performed. The transport phenomena equations include the Navier-Stokes, the respective energy equation for electrolyte, and the radiative transfer equation (RTE). Two different designs, design A, and design B of photo-electrochemical reactors are suggested. The hydrogen production rate and solar-to-hydrogen efficiency are estimated for each design at different solar incident flux ranged from 500 to 2000 W/m2 in increments of 500 W/m2. Results have shown that the solar-to-hydrogen efficiency increases as solar flux increases for both designs. Its predicted values could reach 12.8% for design A, and 13.1% for design B. Moreover, by increasing the solar incident flux, the hydrogen volume production rate is increased as well. It is found to be 79 L/m2.h for design A, and 85.4 L/m2.h for design B. Comparison between currently predicted results and previous data indicates an enhancement of solar-to-hydrogen efficiency and hydrogen production that can be achieved with the suggested design

This paper presents an experimental work to study the effect of the condenser and the medium of saline water types on the performance of the solar still. Single slope solar still facing the south is used in this work. Also, four types of the condenser are tested: (i) glass, (ii) aluminum plate, (iii) aluminum heat sink with pin fins, and (iv) aluminum plate covered with an umbrella. Moreover, four mediums of the saline water inside the basin are examined: (i) only saline water in the basin, (II) Layers of black steel fibers in the basin, (iii) saturated sand with saline water, and (iv) mixture of sand and black steel fibers saturated with saline water. The solar still of only glass walls and only saline water in the basin is taken as a reference case. The performance of the other cases is referred to the reference case. The results indicate that using heat sink condenser increases the temperature of the saline water. Also, it increases the temperature difference between the condenser and the saline water relative to using glass condenser. Also, using a glass condenser with black steel fibers inside the water basin increases the daily productivity of freshwater by 35%. Using the heat sink condenser increases the daily productivity from 31% in the case of using only saline water to 52% in the case of using black steel fibers in the basin. Using an umbrella of 20 cm wide at the top of the aluminum plate condenser decreases the daily productivity by 26%. Increasing the umbrella wide to 40 cm decreases the daily productivity by 31%.

This paper presents an experimental work to study the effect of the condenser and the medium of saline water types on the performance of the solar still. Single slope solar still facing the south is used in this work. Also, four types of the condenser are tested: (i) glass, (ii) aluminum plate, (iii) aluminum heat sink with pin fins, and (iv) aluminum plate covered with an umbrella. Moreover, four mediums of the saline water inside the basin are examined: (i) only saline water in the basin, (II) Layers of black steel fibers in the basin, (iii) saturated sand with saline water, and (iv) mixture of sand and black steel fibers saturated with saline water. The solar still of only glass walls and only saline water in the basin is taken as a reference case. The performance of the other cases is referred to the reference case. The results indicate that using heat sink condenser increases the temperature of the saline water. Also, it increases the temperature difference between the condenser and the saline water relative to using glass condenser. Also, using a glass condenser with black steel fibers inside the water basin increases the daily productivity of freshwater by 35%. Using the heat sink condenser increases the daily productivity from 31% in the case of using only saline water to 52% in the case of using black steel fibers in the basin. Using an umbrella of 20 cm wide at the top of the aluminum plate condenser decreases the daily productivity by 26%. Increasing the umbrella wide to 40 cm decreases the daily productivity by 31%.

NULL

NULL

NULL

NULL

NULL

NULL